{
  "version": "api-v1.2",
  "handle": "t-house",
  "title": "T HOUSE",
  "url": "https://www.theleva.com/products/t-house",
  "summary": "Design your own T-shaped masonry house in 3D -- and get a real, buildable house out of it. This is a fully parametric masonry configurator, not a picture gallery. Drag the main bar and the wing to length, set the wall and storey heights, pick a gable or hip roof and its pitch, choose the block the ...",
  "description": "Design your own T-shaped masonry house in 3D -- and get a real, buildable house out of it. This is a fully parametric masonry configurator, not a picture gallery. Drag the main bar and the wing to length, set the wall and storey heights, pick a gable or hip roof and its pitch, choose the block the walls are laid in, draw the rooms, place windows and doors on the block module, and watch the 3D model update instantly. Every block, ring beam, rafter, tile, board and screw in the model is a real catalog item -- the configurator generates a complete, priced Bill of Quantities as you build, so what you see is exactly what you order.\nA T plan you shape yourself: a main bar and a wing, each dragged to its own length, the wing sliding along the bar to make one arm longer than the other\nMasonry walls in clay block or concrete block (CMU), laid course by course on a whole-block module with bonded corners -- every whole block, every cut block and the mortar are counted\nReinforced concrete ring beams and lintels over every opening, with the rebar cages, stirrups and tie wire that go into them\nStrip footings under every wall and a ground slab between them, sized to the plan you draw\nA carpenter's roof, cut on site: rafters, purlins, posts, braces and collar ties, with valley rafters where the wing meets the bar and hip and jack rafters on a hipped end -- gable or hip, the pitch and every overhang set by hand\nThe whole roof build-up is drawn and counted: OSB deck, insulation above the rafters or between them, underlay, counter-battens and battens, clay tiles, trapezoidal sheet or standing seam, ridge caps, eave and verge flashings -- every layer cut at the valleys\nTwo facades to switch between: a rendered contact facade on EPS with its mesh, corner beads and plinth, or a ventilated timber cladding, vertical or horizontal, on battens over mineral wool and a breather membrane, with corner trims and lined reveals\nWindows and doors land on the block module, and the wall is relaid around them with a lintel above and plastered reveals inside\nDraw the rooms on the plan and the walls go up with them -- load-bearing walls in the house block, partitions in brick, AAC block or drywall, each with its own lintels, plaster and paint\nA second storey on wood I-joists bearing in the walls, with the OSB deck, a framed stairwell and the stair, and a floating wood floor with its underlay and skirting\nInterior plaster on every masonry face, base coat and finish coat, with corner beads, reinforcing mesh and the interior paint -- all by the square metre and the metre\nGutters and downpipes that follow the eaves, and brick posts under any overhang you pull out deep\nColours for the facade, the timber, the roof, the metalwork, the floors and the walls -- change one and the whole model repaints\nA section tool that cuts the house open on any axis, so you can check every layer of the wall, the floor and the roof before it is built\nStand the finished house on your own plot at full size in augmented reality, straight from your phone\nInstant, itemised Bill of Quantities with real supplier part numbers, in metric or imperial -- down to the mortar, the tile clips and the screws",
  "plan": {
    "what": "the downloadable plans for a design made in the configurator",
    "priceFrom": {
      "amount": "50.0",
      "currencyCode": "USD"
    },
    "priceTo": {
      "amount": "50.0",
      "currencyCode": "USD"
    }
  },
  "configurator": {
    "type": "thouse",
    "url": "https://www.theleva.com/products/t-house",
    "options": null,
    "note": "The options are described for the A-frame, the ADU and the RANCH so far; this product's page has them in 3D."
  },
  "referenceDesigns": null
}